Skip to main content
Appliance Fix Guide

Electrolux Washer error code

Electrolux Washer Error E99

Incongruence between the sound and light module and the main board.

Incongruence between the sound and light module and the main board.

Updated Aug 18, 2026
Diagnose before buying a part
Electrolux washer repair guide for error E99
Error codeE99Washer

Start here before buying a part or taking the appliance apart.

  1. 1
    Check 1

    Disconnect the washer from the power outlet for a few minutes, then reconnect it.

  2. 2
    Check 2

    Unplug the appliance and inspect the wiring between the audio unit and the main electronic unit for any loose or damaged connections.

  3. 3
    Check 3

    Visually inspect the sound block for any signs of damage.

A quick explanation

What does E99 mean?

Incongruence between the sound and light module and the main board.

The answer you came for

How to fix Electrolux washer error E99

Start with the safest checks and work from simple to technical.

  1. 1

    Step 1

    1. Disconnect the washer from power by unplugging it from the wall outlet to ensure safety.

  2. 2

    Step 2

    2. Remove the top panel of the washer. This is typically secured by two screws on the back of the machine. Slide the panel back and lift it off.

  3. 3

    Step 3

    3. Locate the main control board, usually housed in a plastic casing near the front control panel, and the sound/light module.

  4. 4

    Step 4

    4. Carefully disconnect the wiring harness that connects the main board to the sound and light module. Pay close attention to the connector clips to avoid damage.

  5. 5

    Step 5

    5. Remove the old loudspeaker and wiring harness. The loudspeaker may be attached with small screws or clips. Replace them with the new parts.

  6. 6

    Step 6

    6. Securely connect the new wiring harness to both the main control board and the new loudspeaker/light module, ensuring all connections are snug.

  7. 7

    Step 7

    7. Reassemble the washer by replacing the top panel and securing it with the screws. Plug the washer back in and run a test cycle to confirm the error is resolved.

Read the additional checks from the current guide

How to Fix E99 Error (Step-by-Step) Disconnect the washer from power by unplugging it from the wall outlet to ensure safety. Remove the top panel of the washer. This is typically secured by two screws on the back of the machine. Slide the panel back and lift it off. Locate the main control board, usually housed in a plastic casing near the front control panel, and the sound/light module. Carefully disconnect the wiring harness that connects the main board to the sound and light module. Pay close attention to the connector clips to avoid damage. Remove the old loudspeaker and wiring harness. The loudspeaker may be attached with small screws or clips. Replace them with the new parts. Securely connect the new wiring harness to both the main control board and the new loudspeaker/light module, ensuring all connections are snug. Reassemble the washer by replacing the top panel and securing it with the screws. Plug the washer back in and run a test cycle to confirm the error is resolved. Turn the appliance off, wait about 2 minutes, then turn it back on.

What to Check Next on This Electrolux Washer Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test. Disconnect power before opening panels, then confirm whether the Electrolux washer repeats the same code after a clean reset. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure. Use the complete Electrolux washer model number from the appliance tag before ordering any model-specific part. Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering. Parts Availability Note: For this Electrolux/Frigidaire error code, exact OEM part numbers can vary by model revision and serial range. We’ve listed the most likely component(s), but confirm compatibility using your full model number before ordering. If no exact SKU is shown, use this guide for diagnosis first, then verify the matching OEM part on RepairClinic or PartSelect. Recommended Parts to Check No exact official OEM part number is listed here because the correct Electrolux washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims. Electrolux washer drain pump Common replacement category: Drain pump Fit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying. Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks. Search Amazon for Electrolux washer drain pump Electrolux washer water inlet valve Common replacement category: Water inlet valve Fit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying. Why this category can matter: fill and slow-fill symptoms after supply checks. Search Amazon for Electrolux washer water inlet valve Electrolux washer door lock Common replacement category: Door lock / latch Fit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying. Why this category can matter: start, lock, or spin symptoms tied to door-lock feedback. Search Amazon for Electrolux washer door lock Before ordering: match the part to the complete Electrolux washer model number on the appliance tag. Still Not Working? If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure. Browse all Electrolux error codes: Electrolux Error Codes

If the code comes back

Do not keep replacing parts based only on the code. Repeat the safe checks above. If the fault remains, stop and arrange qualified service rather than ordering from the code alone.

What may be causing it?

  • Communication error between the sound block and the main electronic unit
  • Faulty sound block
  • Faulty main electronic unit

These are possibilities to investigate, not proof that one part has failed.

Recommended part

Recommended part for this error code

No replacement part recommended for this code

The researched guidance for Electrolux Washer error E99 points to user-action and diagnostic steps above rather than a mapped replacement part. We will not invent a part or send you to an unrelated product.

Replacement options

Ready to replace your washer?

If repairing this washer no longer feels worthwhile, compare three replacement paths below.

Why shop your replacement on Amazon?

  • Fast, free delivery

    Prime members can get fast, free delivery on eligible items.

  • Convenient delivery options

    Select large appliances may offer scheduled or Room of Choice delivery.

  • Haul-away options

    Haul-away may be available for select appliances and delivery areas.

  • Installation help

    Installation or assembly may be available on select items.

Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Make the money decision

Repair or replace calculator

Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.