Skip to main content
Appliance Fix Guide

Electrolux Washer error code

Electrolux Washer Error E73

Fault in the dryer temperature sensor circuit.

Fault in the dryer temperature sensor circuit.

Updated Aug 18, 2026
Diagnose before buying a part
Electrolux washer repair guide for error E73
Error codeE73Washer

Start here before buying a part or taking the appliance apart.

  1. 1
    Check 1

    Turn the appliance off and on to see if the error code clears.

  2. 2
    Check 2

    Check the wiring to the drying NTC sensor for any damage or loose connections.

  3. 3
    Check 3

    Visually inspect the NTC sensor located on the drying duct. If it appears damaged, it will need to be replaced.

A quick explanation

What does E73 mean?

Fault in the dryer temperature sensor circuit.

The answer you came for

How to fix Electrolux washer error E73

Start with the safest checks and work from simple to technical.

  1. 1

    Step 1

    1. Power down the washer and unplug it from the electrical outlet.

  2. 2

    Step 2

    2. Remove the rear access panel to find the dryer temperature sensor on the heater assembly.

  3. 3

    Step 3

    3. Carefully detach the electrical connector from the sensor.

  4. 4

    Step 4

    4. Inspect the wiring and the sensor for any visible signs of damage or corrosion.

  5. 5

    Step 5

    5. Test the sensor's resistance with a multimeter; it should be within the manufacturer's specified range.

  6. 6

    Step 6

    6. Replace the sensor if it is out of range or damaged by unscrewing it from the housing.

  7. 7

    Step 7

    7. Secure the new sensor, reconnect the wiring, and reattach the rear panel before testing.

Read the additional checks from the current guide

How to Fix E73 Error (Step-by-Step) Power down the washer and unplug it from the electrical outlet. Remove the rear access panel to find the dryer temperature sensor on the heater assembly. Carefully detach the electrical connector from the sensor and confirm the error stays cleared during a full test cycle. Inspect the wiring and the sensor for any visible signs of damage or corrosion. Test the sensor’s resistance with a multimeter; it should be within the manufacturer’s specified range. Replace the sensor if it is out of range or damaged by unscrewing it from the housing. Secure the new sensor, reconnect the wiring, and reattach the rear panel before testing. Turn the appliance off, wait about 2 minutes, then turn it back on. Recommended Parts to Check No exact official OEM part number is listed here because the correct Electrolux washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims. Electrolux washer drain pump Common replacement category: Drain pump Fit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying. Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks. Search Amazon for Electrolux washer drain pump Electrolux washer water inlet valve Common replacement category: Water inlet valve Fit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying. Why this category can matter: fill and slow-fill symptoms after supply checks. Search Amazon for Electrolux washer water inlet valve Electrolux washer door lock Common replacement category: Door lock / latch Fit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying. Why this category can matter: start, lock, or spin symptoms tied to door-lock feedback. Search Amazon for Electrolux washer door lock Before ordering: match the part to the complete Electrolux washer model number on the appliance tag. Still Not Working? If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure. Browse all Electrolux error codes: Electrolux Error Codes

If the code comes back

Do not keep replacing parts based only on the code. Repeat the safe checks above. If the fault remains, stop and arrange qualified service rather than ordering from the code alone.

What may be causing it?

  • Drying NTC sensor failure
  • Damaged or loose wiring to the drying NTC sensor

These are possibilities to investigate, not proof that one part has failed.

Recommended part

Recommended part for this error code

Replacement part

OEM candidate: 3792171203

Price noted in the current guide: $18-$93

Why this part is shown: It is associated with Electrolux Washer error E73 in the current guide. The error code alone does not prove this part has failed.

Compatibility varies by model. Confirm that the Amazon listing includes your complete washer model number before ordering.

Amazon part link View recommended part on Amazon

You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Replacement options

Ready to replace your washer?

If repairing this washer no longer feels worthwhile, compare three replacement paths below.

Why shop your replacement on Amazon?

  • Fast, free delivery

    Prime members can get fast, free delivery on eligible items.

  • Convenient delivery options

    Select large appliances may offer scheduled or Room of Choice delivery.

  • Haul-away options

    Haul-away may be available for select appliances and delivery areas.

  • Installation help

    Installation or assembly may be available on select items.

Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Make the money decision

Repair or replace calculator

Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.

Safety first

Disconnect power before opening panels or touching internal parts.

When to stop
  • Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
  • Do not perform live-voltage testing unless you are trained and equipped for it.
  • Use the exact model manual or service information before replacing electronic controls.

Free quick sheet

Get the Electrolux Washer Error Code Quick Sheet

A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.

The form will be enabled after the existing subscriber database and PDF delivery are connected securely.

No spam. Unsubscribe anytime.