Skip to main content
Appliance Fix Guide

Electrolux Washer error code

Electrolux Washer Error E70

Temperature Sensor Error - Issue with the water temperature sensor (NTC thermistor).

Temperature Sensor Error - Issue with the water temperature sensor (NTC thermistor).

Updated Aug 18, 2026
Diagnose before buying a part
Electrolux washer repair guide for error E70
Error codeE70Washer

Try these first

Start here before buying a part or taking the appliance apart.

  1. 1
    Check 1

    Turn the washer off and on again to see if the code clears.

  2. 2
    Check 2

    Check the wiring to the NTC (temperature) sensor for any loose or damaged connections.

  3. 3
    Check 3

    Use a multimeter to check the resistance of the NTC sensor.

A quick explanation

What does E70 mean?

Temperature Sensor Error - Issue with the water temperature sensor (NTC thermistor).

The answer you came for

How to fix Electrolux washer error E70

Start with the safest checks and work from simple to technical.

  1. 1

    Step 1

    1. Disconnect the power cord of the washer from the wall outlet.

  2. 2

    Step 2

    2. Locate the water temperature sensor (NTC thermistor). It is usually pushed into a rubber grommet on the wash tub or mounted directly on the heating element assembly.

  3. 3

    Step 3

    3. You may need to remove the front or rear service panel for access.

  4. 4

    Step 4

    4. Disconnect the two wires leading to the sensor.

  5. 5

    Step 5

    5. Set a multimeter to measure resistance in Ohms (Ω). Test the sensor by placing a probe on each of its two terminals.

  6. 6

    Step 6

    6. At room temperature, you should get a reading of several thousand ohms. If the reading is zero or infinite (OL), the sensor is defective and must be replaced.

  7. 7

    Step 7

    7. Pull the old sensor out and install the new one, then reconnect the wires, reattach the panel, and restore power.

Read the additional checks from the current guide

How to Fix E70 Error (Step-by-Step) Disconnect the power cord of the washer from the wall outlet. Locate the water temperature sensor (NTC thermistor). It is usually pushed into a rubber grommet on the wash tub or mounted directly on the heating element assembly. You may need to remove the front or rear service panel for access. Disconnect the two wires leading to the sensor and confirm the error stays cleared during a full test cycle. Set a multimeter to measure resistance in Ohms (Ω). Test the sensor by placing a probe on each of its two terminals. At room temperature, you should get a reading of several thousand ohms. If the reading is zero or infinite (OL), the sensor is defective and must be replaced. Pull the old sensor out and install the new one, then reconnect the wires, reattach the panel, and restore power. Turn the appliance off, wait about 2 minutes, then turn it back on. Verified Compatible Alternatives: 807165801 Recommended Parts to Check No exact official OEM part number is listed here because the correct Electrolux washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims. Electrolux washer drain pump Common replacement category: Drain pump Fit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying. Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks. Search Amazon for Electrolux washer drain pump Electrolux washer water inlet valve Common replacement category: Water inlet valve Fit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying. Why this category can matter: fill and slow-fill symptoms after supply checks. Search Amazon for Electrolux washer water inlet valve Electrolux washer door lock Common replacement category: Door lock / latch Fit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying. Why this category can matter: start, lock, or spin symptoms tied to door-lock feedback. Search Amazon for Electrolux washer door lock Before ordering: match the part to the complete Electrolux washer model number on the appliance tag. Still Not Working? If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure. Browse all Electrolux error codes: Electrolux Error Codes

If the code comes back

Do not keep replacing parts based only on the code. Repeat the safe checks above. If the fault remains, stop and arrange qualified service rather than ordering from the code alone.

What may be causing it?

  • Faulty NTC temperature sensor
  • Damaged or loose wiring to the NTC sensor

These are possibilities to investigate, not proof that one part has failed.

Recommended part

Recommended part for this error code

Replacement part

OEM candidate: 8588071658013

Price noted in the current guide: $5-$95

Why this part is shown: It is associated with Electrolux Washer error E70 in the current guide. The error code alone does not prove this part has failed.

Compatibility varies by model. Confirm that the Amazon listing includes your complete washer model number before ordering.

Amazon part link View recommended part on Amazon

You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Replacement options

Ready to replace your washer?

If repairing this washer no longer feels worthwhile, compare three replacement paths below.

Why shop your replacement on Amazon?

  • Fast, free delivery

    Prime members can get fast, free delivery on eligible items.

  • Convenient delivery options

    Select large appliances may offer scheduled or Room of Choice delivery.

  • Haul-away options

    Haul-away may be available for select appliances and delivery areas.

  • Installation help

    Installation or assembly may be available on select items.

Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Make the money decision

Repair or replace calculator

Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.

Safety first

Disconnect power before opening panels or touching internal parts.

When to stop
  • Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
  • Do not perform live-voltage testing unless you are trained and equipped for it.
  • Use the exact model manual or service information before replacing electronic controls.

Free quick sheet

Get the Electrolux Washer Error Code Quick Sheet

A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.

The form will be enabled after the existing subscriber database and PDF delivery are connected securely.

No spam. Unsubscribe anytime.