Error Code: F11 Difficulty: Hard
Problem: Electronics problem; may require diagnostics and replacement of the power unit.
How to Fix F11 Error (Step-by-Step)
- Disconnect the dryer from the power source by unplugging it from the wall outlet.
- Locate the moisture sensor bars, which are two metallic strips typically found on the lint filter housing just inside the dryer door. Clean the sensors with a cotton ball and rubbing alcohol to remove any residue or buildup.
- To access the main control board, you will likely need to remove the top panel of the dryer by unscrewing the screws at the back or sides.
- Before touching the control board, ground yourself by touching a metal part of the dryer to discharge any static electricity. Carefully disconnect the wire harnesses connected to the old control board, taking a picture beforehand for reference can be helpful.
- Remove the screws holding the old control board in place and gently lift it out.
- Install the new main control board, securing it with the screws and reconnecting the wire harnesses as they were on the old board.
- Reassemble the dryer by securing the top panel, and then plug the dryer back into the power outlet to test its functionality.
- Turn the appliance off, wait about 2 minutes, then turn it back on.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
What to Check Next on This Bosch Dryer
Use these checks before ordering parts for Bosch dryer F11. They keep the diagnosis tied to the appliance instead of turning the page into a reset-only guide.
- Unplug the dryer before touching the lint housing, rear vent, lower service area, or any wiring.
- Clean the lint screen, moisture sensor bars, condenser area if equipped, and the full vent path so airflow problems do not imitate part failures.
- Run a short timed cycle with a light load and note whether the fault appears immediately, after heating starts, or near the end of the cycle.
- If the fault returns with clean airflow, inspect the part categories below using the full model number from the dryer tag.
- Stop repeated test cycles if you smell heat, see moisture near electrical areas, or hear grinding from the drum drive.
Recommended Parts to Check
Bosch dryer part numbers vary by model. These are model-number-safe part-category searches, not universal fit claims.
-
Dryer lint screenCommon replacement category: lint filterFit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.Why check it: Start with lint restrictions when heating, airflow, or maintenance warnings appear.
-
Dryer thermal fuseCommon replacement category: thermal protectionFit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.Why check it: Common safety device to inspect after overheating or no-heat symptoms.
-
Dryer drum beltCommon replacement category: drive systemFit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.Why check it: Worth checking when the dryer tumbles poorly, stalls, or makes drive noise.
-
Dryer moisture sensorCommon replacement category: sensor circuitFit note: Exact OEM part number varies by full model number. Confirm compatibility before buying.Why check it: Useful category to verify when dryness or care/maintenance messages persist.
Before ordering: match the part to the complete model number on the appliance tag.
More options (for a better recommendation)
⚡ Don’t Risk a DIY Fail!
Get the ‘Secret Service Mode’ Cheat Sheet for your Bosch model. Includes an easy-to-read list of every error code and quick diagnostic tips.
✅ Join 15,000+ DIYers • Instant PDF Download
Browse More Codes
📖 View All Error Codes
Expert: Mike Sullivan
EPA Section 608 Certified Technician with 18+ years experience.
Read Editorial Standards →Browse all Bosch error codes: Bosch Error Codes
When It’s Better to Replace Than Repair
Dryer repairs are often worth it for small parts, but repeated heating, motor, drum, or control failures can point toward replacement.
Confirm gas vs electric, venting, voltage, doorway clearance, and laundry-space dimensions before ordering.
For repair parts, verify exact fit with the full dryer model number before buying; these links are general replacement-appliance shopping options.
- [OK]Thermal fuse or heater failures keep returning
- [OK]Belt, roller, or motor repairs exceed unit value
- [OK]Door switch or control issues stack with other faults
- [OK]Older dryer has long dry times even after vent cleaning
Recommended Dryer Replacement Options
As an Amazon Associate, we earn from qualifying purchases.
Leave a Reply