Author: ApplianceFixGuide Team

  • How to Fix LG Dryer Error FE

    How to Fix LG Dryer Error FE

    Problem: Fill Error (Washer/Dryer Combo). The water valve is stuck open, filling the unit with water during the dry cycle.

    How to Fix Dryer Error

    1. Turn off the water supply taps behind the unit.
    2. Unplug the unit.
    3. If water continues to flow, the valve is mechanically seized.
    4. Replace the water inlet valve assembly.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Dryer Error PE

    How to Fix LG Dryer Error PE

    Problem: Pressure Sensor Error (Washer/Dryer Combo). The water level sensor is malfunctioning.

    How to Fix Dryer Error

    1. Unplug the unit.
    2. Remove the top panel.
    3. Locate the pressure switch (round plastic component with a small rubber hose).
    4. Check the wiring harness and the rubber hose for punctures.
    5. Replace the pressure switch.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Dryer Error CF

    How to Fix LG Dryer Error CF

    Problem: Clean Filter. A logic prompt indicating the lint filter must be cleaned.

    How to Fix Dryer Error

    1. Remove the lint filter.
    2. Clean off all lint.
    3. Reinsert the filter.
    4. Press Start to resume.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Dryer Error Gas_Reset

    How to Fix LG Dryer Error Gas_Reset

    Problem: No Heat (Gas) – Not a display code, but a system state. Thermal fuse tripped.

    How to Fix Dryer Error

    1. Unplug the dryer.
    2. Remove the back panel or front ductwork to access the blower housing.
    3. Locate the white thermal fuse on the blower housing.
    4. Test for continuity. If open (no beep), the fuse has blown due to overheating (usually a clogged vent).
    5. Replace the fuse and clean the vent.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Dryer Error Elec_Reset

    How to Fix LG Dryer Error Elec_Reset

    Problem: No Heat (Electric) – Not a display code, but a system state. High Limit Thermostat tripped.

    How to Fix Dryer Error

    1. Unplug the dryer.
    2. Access the heating element housing.
    3. Locate the high-limit thermostat (small disc on the heater can).
    4. Test for continuity. If open, the thermostat cut power to the heater.
    5. Replace the thermostat and check airflow.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Lg error codes: Lg Error Codes

  • How to Fix LG Dryer Error LE1

    How to Fix LG Dryer Error LE1

    Problem: Motor Locked Error. The drum is overloaded or the motor is physically seized.

    How to Fix Dryer Error

    1. Open the door and remove some wet clothes (reduce load size).
    2. Try to spin the drum by hand; it should offer resistance but move.
    3. If the drum is stuck solid, check for objects wedged between the drum and bulkhead.
    4. If drum moves but code persists, the motor windings or Hall sensor (if equipped) are bad. Replace motor.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You




    Browse all Lg error codes: Lg Error Codes

  • How to Fix Samsung Dishwasher Error 1E

    How to Fix Samsung Dishwasher Error 1E

    Problem: Inlet water temperature sensor fault; thermistor open, shorted, or out of operational range

    How to Fix Dishwasher Error

    1. Unplug dishwasher from electrical power or switch off dedicated circuit breaker.
    2. Remove lower access panel beneath dishwasher door using Phillips screwdriver.
    3. Locate inlet water thermistor (mounted on water inlet valve assembly near sump). Disconnect wiring harness.
    4. Measure resistance across thermistor terminals with multimeter set to resistance mode at room temperature (77°F/25°C). Expected value: 10kΩ ±10%. Infinite resistance = open circuit; near zero = shorted.
    5. Remove mounting screw securing sensor. Gently extract thermistor from housing.
    6. Clean mounting well thoroughly with isopropyl alcohol and lint-free cloth.
    7. Apply thin layer of thermal conductive paste to sensing tip of new sensor.
    8. Install replacement thermistor using OEM part DD31-00003A. Secure mounting screw to 4 in-lbs torque.
    9. Reconnect wiring harness until audible click. Reinstall access panel.
    10. Restore power. Run diagnostic cycle (press Temp+Delay Start+Power) to verify error cleared and temperature readings stabilize.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dishwasher Error 3C

    How to Fix Samsung Dishwasher Error 3C

    Problem: Water supply error; insufficient water pressure or flow during fill cycle

    How to Fix Dishwasher Error

    1. Verify household water supply valve to dishwasher is fully open (turn counterclockwise until stop).
    2. Check water supply hose for kinks, crushing, or blockages behind dishwasher.
    3. Disconnect supply hose from dishwasher inlet valve. Place towel underneath. Briefly open valve to confirm strong water flow into container.
    4. Clean inlet screen filter inside valve port using old toothbrush and white vinegar solution. Rinse thoroughly under running water.
    5. Reconnect supply hose hand-tight plus 1/4 turn. Ensure no leaks at connection.
    6. Confirm household water pressure is minimum 20 PSI using pressure gauge at nearby faucet.
    7. Restore power. Start Normal cycle and verify dishwasher fills to proper level within 90 seconds.
    8. If error recurs, check for closed saddle valve or clogged household water filter upstream.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dishwasher Error 3E

    How to Fix Samsung Dishwasher Error 3E

    Problem: Water leakage detected; moisture sensor activated under tub assembly

    How to Fix Dishwasher Error

    1. Immediately unplug dishwasher and turn off water supply valve.
    2. Remove standing water from bottom pan using wet/dry vacuum or towels.
    3. Tilt dishwasher forward carefully (with assistance) to access base. Locate moisture sensor pad under tub.
    4. Dry sensor pad thoroughly with lint-free cloth. Allow 60 minutes air drying time.
    5. Inspect all hoses, pump housing, tub seams, and door gasket for leaks. Pay close attention to spray arm seals and detergent dispenser gasket.
    6. Tighten any loose hose clamps using pliers. Replace cracked hoses or damaged gaskets.
    7. If sensor remains triggered after drying and leak repair, replace moisture sensor using OEM part DD31-00005A.
    8. Reassemble panels. Restore water and power. Run short cycle with panels off to visually confirm no leaks before final reassembly.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Samsung error codes: Samsung Error Codes

  • How to Fix Samsung Dishwasher Error 4C

    How to Fix Samsung Dishwasher Error 4C

    Problem: Water inlet restriction; clogged filter screen at inlet valve

    How to Fix Dishwasher Error

    1. Turn off water supply valve and unplug dishwasher.
    2. Place towel under inlet valve area (lower left behind access panel).
    3. Disconnect water supply hose from inlet valve. Have container ready for residual water.
    4. Remove brass inlet screen filter from valve port using needle-nose pliers.
    5. Soak filter in white vinegar solution for 15 minutes. Scrub gently with soft brush to remove mineral deposits and debris.
    6. Rinse filter thoroughly under running water until water runs clear.
    7. Reinstall clean filter into valve port. Reconnect supply hose hand-tight plus 1/4 turn.
    8. Restore water supply. Check connection for leaks. Plug in dishwasher.
    9. Run Rinse cycle to verify proper water fill level and absence of error code.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.

    Ask a Technician Online – Get Answer in Minutes
    Find a Local Repair Pro Near You



    Browse all Samsung error codes: Samsung Error Codes