Author: ApplianceFixGuide Team

  • How to Fix Whirlpool Washer Error LO

    How to Fix Whirlpool Washer Error LO

    Problem: Lock open – door/lid lock mechanism failed to engage

    How to Fix Washer Error

    1. Unplug washer and verify door/lid closes fully without obstruction.
    2. Remove appropriate panel (kick panel for front-load, top panel for top-load) to access lock assembly.
    3. Manually operate lock mechanism – should move smoothly between locked/unlocked positions.
    4. Disconnect lock wiring harness and measure resistance across coils (primary 300-600 ohms, secondary 1000-1500 ohms).
    5. Verify 120V AC reaches lock during operation (test at connector with door closed).
    6. Inspect lock strike plate alignment – misalignment prevents proper engagement.
    7. Check wiring harness between lock and control board for damage near moving parts.
    8. If lock mechanism binds mechanically, lubricate pivot points with silicone grease (do not use petroleum-based lubricants).
    9. If electrical tests fail or mechanism is damaged, replace door/lid lock assembly WPW
    10. After replacement, verify lock engages within 3 seconds of cycle start and washer won’t operate with door/lid ajar.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Whirlpool Washer Error F0E0

    How to Fix Whirlpool Washer Error F0E0

    Problem: No error code stored – communication failure between control boards preventing code retrieval

    How to Fix Washer Error

    1. Unplug washer for 10 minutes to fully reset all control boards.
    2. Remove top panel to access main control board (CCU) connections.
    3. Disconnect and reconnect all wire harnesses at CCU, especially serial communication cables.
    4. Inspect harness routing for pinch points between cabinet panels or near moving components.
    5. Check for moisture damage or corrosion on board connectors – clean with electrical contact cleaner if needed.
    6. Verify 120V AC power supply to CCU is stable (no voltage sags during operation).
    7. Enter diagnostic mode per model-specific procedure to force error code display.
    8. If F0E0 persists after harness reseating, suspect corrupted EEPROM on CCU.
    9. Replace main control board assembly W
    10. After replacement, run full diagnostic cycle and document any new error codes that appear for further troubleshooting.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error F12

    How to Fix Kenmore Washer Error F12

    Problem: User interface control board failure

    How to Fix Washer Error

    1. Disconnect power at circuit breaker.
    2. Remove control panel faceplate and access cover.
    3. Inspect user interface board for damage or burnt components.
    4. Test membrane switch pad for proper contact operation.
    5. Check communication wires between interface and main control.
    6. If interface board is faulty, disconnect all connectors.
    7. Remove mounting screws and replace user interface assembly.
    8. Reconnect all harnesses and test display functions.
    9. Calibrate touch controls if required.
    10. Run diagnostic mode to verify all button operations.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error F29

    How to Fix Kenmore Dryer Error F29

    Problem: Temperature sensor failure during heavy duty cycle

    How to Fix Dryer Error

    1. Turn off power supply.
    2. Remove rear access panel.
    3. Locate thermistor sensor on heater assembly.
    4. Disconnect electrical connector from sensor.
    5. Test sensor resistance with multimeter at room temperature.
    6. Compare readings to manufacturer specifications.
    7. If sensor is faulty, remove mounting screws and replace sensor.
    8. Check wiring harness for damage or corrosion.
    9. Inspect heater element connections for proper contact.
    10. Restore power and test heavy duty cycle operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Whirlpool Washer Error F0E4

    How to Fix Whirlpool Washer Error F0E4

    Problem: Shifter position error – transmission not in correct position for selected cycle

    How to Fix Washer Error

    1. Unplug washer and remove front lower panel.
    2. Locate shifter assembly mounted between transmission and tub (Cabrio models).
    3. Manually move shifter lever between wash/spin positions – should move smoothly without binding.
    4. Inspect shifter linkage for bent components, excessive play, or disconnected rods.
    5. Disconnect shifter wiring harness and measure resistance across position sensor (should be 1000-2000 ohms).
    6. Verify 120V AC reaches shifter during mode change (test at connector during cycle transition).
    7. Check transmission input shaft for smooth rotation in both directions without grinding.
    8. Inspect tub for foreign objects jamming transmission engagement.
    9. If shifter doesn’t move when powered or position sensor readings are erratic, replace shifter assembly W
    10. After replacement, verify washer agitates during wash cycle and spins during spin cycle without hesitation or error codes.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Whirlpool Washer Error F0E5

    How to Fix Whirlpool Washer Error F0E5

    Problem: Unbalanced load detected during spin (Cabrio platform equivalent of uL)

    How to Fix Washer Error

    1. Washer will automatically pause and attempt to redistribute load – allow 5-10 minutes for this process.
    2. If automatic rebalance fails, open lid and manually redistribute laundry evenly around tub perimeter.
    3. Remove bulky items (comforters, rugs) and wash separately with towels for balance.
    4. Avoid washing single heavy items alone – always add smaller items to distribute weight.
    5. Ensure washer is level front-to-back and side-to-side (use carpenter’s level on top panel).
    6. Adjust leveling legs until all four feet contact floor firmly without rocking.
    7. Verify suspension rods aren’t broken or disconnected (requires removing cabinet panels to inspect).
    8. Check tub bearings for excessive play allowing tub to shift during spin.
    9. If uL occurs repeatedly with balanced loads, suspect failing tub bearing or broken counterweight.
    10. After redistribution, close lid and press START to resume cycle – allow washer to complete automatic rebalance attempts.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dryer Error F28

    How to Fix Kenmore Dryer Error F28

    Problem: Temperature sensor failure during delicate cycle

    How to Fix Dryer Error

    1. Disconnect power at circuit breaker.
    2. Remove rear access panel.
    3. Locate thermistor sensor on blower housing.
    4. Disconnect electrical connector from sensor.
    5. Test sensor resistance with multimeter at room temperature.
    6. Compare readings to manufacturer specifications.
    7. If sensor is faulty, remove mounting screws and replace sensor.
    8. Check wiring harness for damage or corrosion.
    9. Inspect heater circuit relays for proper operation.
    10. Restore power and test delicate cycle operation.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Whirlpool Washer Error F1E1

    How to Fix Whirlpool Washer Error F1E1

    Problem: Main control board EEPROM failure – corrupted memory preventing normal operation

    How to Fix Washer Error

    1. Unplug washer for 10 minutes to fully discharge board capacitors.
    2. Remove top panel and locate main control board (CCU) in upper right cabinet area.
    3. Inspect board for visible damage: burnt components, bulging capacitors, or moisture corrosion.
    4. Check all wire harness connections for proper seating and corrosion – reseat firmly.
    5. Verify 120V AC power supply to board is stable (no voltage sags during operation).
    6. If board appears physically intact but error persists after power cycle, EEPROM corruption has occurred.
    7. Main control board must be replaced – EEPROM cannot be reprogrammed in field service.
    8. Install new CCU W10461397 and secure all mounting screws to prevent vibration damage.
    9. After installation, run full diagnostic cycle to verify all functions operate correctly.
    10. Note: Power surges often cause this failure – recommend installing whole-house surge protector to prevent recurrence.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Dishwasher Error F09

    How to Fix Kenmore Dishwasher Error F09

    Problem: Drying fan motor failure or blocked air circulation

    How to Fix Dishwasher Error

    1. Access drying fan assembly in door or top panel.
    2. Check fan blades for obstructions or damage.
    3. Test fan motor for continuity and proper operation.
    4. Inspect thermal fuse on fan assembly.
    5. Verify control signals to fan motor during dry cycle.
    6. Replace drying fan assembly if necessary.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.


  • How to Fix Kenmore Washer Error F11

    How to Fix Kenmore Washer Error F11

    Problem: Motor control board failure

    How to Fix Washer Error

    1. Turn off power at circuit breaker.
    2. Remove front access panel and motor control board cover.
    3. Inspect motor control board for burnt components or damaged traces.
    4. Check all wire connections for proper seating and corrosion.
    5. Test voltage supply to motor control board.
    6. If board shows physical damage, document all wire connections.
    7. Remove mounting screws and disconnect all connectors.
    8. Install new motor control board assembly.
    9. Reconnect all harnesses in correct positions.
    10. Power up and test motor operation at various speeds.

    Still Not Working?

    If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.