Author: ApplianceFixGuide Team

How to Fix Kenmore Washer Error F30
Problem: Control board logic failure – system crash

How to Fix Washer Error
1. Disconnect power at circuit breaker.
2. Remove control panel and main access covers.
3. Inspect all control boards for physical damage or burnt components.
4. Check all wire harness connections for proper seating and corrosion.
5. Test voltage supply to all control boards.
6. Attempt to reset by disconnecting power for 20 minutes.
7. If error persists, document all wire connections before removal.
8. Replace main control board assembly first.
9. If error continues, replace user interface board.
10. Reconnect all harnesses and run complete diagnostic cycle.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 2, 2026
How to Fix Kenmore Dryer Error OL
Problem: Overload protection activated – motor overheating

How to Fix Dryer Error
1. Turn off power supply and allow dryer to cool completely.
2. Remove front access panel.
3. Inspect drive motor for overheating signs or unusual smells.
4. Check motor cooling fan for obstructions or damage.
5. Test motor windings with multimeter for proper resistance.
6. Inspect drum belt for proper tension and wear.
7. Check drum rollers and bearings for excessive friction.
8. Clean motor and surrounding area with compressed air.
9. Verify proper ventilation around dryer unit.
10. Test motor operation under reduced load conditions.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 2, 2026
How to Fix Kenmore Dryer Error FL
Problem: Lint filter reminder – filter needs cleaning

How to Fix Dryer Error
1. Turn off power supply and allow dryer to cool.
2. Remove lint filter from housing.
3. Clean lint filter thoroughly under warm running water with mild soap.
4. Use soft brush to remove embedded lint and debris.
5. Rinse filter completely and allow to dry completely.
6. Inspect lint filter housing for accumulated lint and debris.
7. Clean housing with vacuum cleaner and soft brush.
8. Reinstall clean lint filter ensuring proper seating.
9. Reset lint filter reminder through control panel if available.
10. Test dryer operation and monitor for proper airflow.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 2, 2026
How to Fix Kenmore Washer Error F29
Problem: Door lock circuit failure during safety checks

How to Fix Washer Error
1. Turn off power supply.
2. Open washer door fully.
3. Inspect door lock assembly wiring harness for damage.
4. Test door lock solenoid resistance with multimeter under various conditions.
5. Check door switch continuity and proper operation.
6. Inspect door strike plate for alignment and wear.
7. If lock circuit is faulty, replace door lock assembly.
8. Verify proper electrical connections and grounding.
9. Test door lock function during different cycle phases.
10. Ensure safety interlocks are functioning before final testing.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 2, 2026
How to Fix Kenmore Washer Error F28
Problem: Motor control communication failure with main board

How to Fix Washer Error
1. Turn off power at circuit breaker.
2. Remove front access panel and motor control board cover.
3. Inspect communication connectors between motor and main control boards.
4. Check wiring harness for damage, pinched wires, or corrosion.
5. Test communication signals with multimeter if possible.
6. Clean all electrical contacts with contact cleaner.
7. If connections are good but error persists, replace motor control board.
8. Document all wire connections before disconnecting.
9. Install new motor control board assembly.
10. Test motor operation and verify communication with main control.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 2, 2026
How to Fix Kenmore Dryer Error dE
Problem: Door open error during cycle operation

How to Fix Dryer Error
1. Turn off power supply.
2. Open dryer door fully.
3. Inspect door latch mechanism for debris or physical damage.
4. Check door strike plate alignment with latch mechanism.
5. Test door switch continuity with multimeter.
6. Inspect door lock solenoid for proper operation.
7. Check wiring harness for damage or loose connections.
8. If door lock assembly is faulty, disconnect electrical connector.
9. Remove mounting screws and replace door lock assembly.
10. Ensure proper alignment during installation and test door closure function.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 2, 2026
How to Fix Kenmore Washer Error F27
Problem: Overflow condition detected – excessive water level

How to Fix Washer Error
1. Turn off power and water supply immediately.
2. Remove standing water from washer bottom with towels or wet vacuum.
3. Check pressure switch tube for kinks, cracks, or disconnections.
4. Inspect water level pressure switch for proper operation.
5. Test pressure switch contacts with multimeter while blowing into tube.
6. Check inlet valve operation for proper shut-off function.
7. Inspect drain pump for blockages preventing drainage.
8. Clean pressure switch tube and connections thoroughly.
9. Test fill cycle with manual monitoring to verify proper water level.
10. Run diagnostic cycle to clear error code.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 2, 2026
How to Fix Kenmore Dryer Error UE
Problem: Unbalanced load detected during spin cycle

How to Fix Dryer Error
1. Pause the drying cycle immediately.
2. Open dryer door and redistribute laundry evenly around drum.
3. Remove any large, heavy items that may cause imbalance.
4. Add a few smaller items to help balance the load if needed.
5. Close door and restart the drying cycle.
6. If imbalance persists, reduce drying time setting for this load.
7. Check dryer leveling by adjusting feet until bubble level shows level.
8. Ensure all four feet are firmly on floor and not rocking.
9. For future loads, distribute items of similar weight evenly around drum.
10. Test with balanced load to verify proper drying operation.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 2, 2026
How to Fix Kenmore Washer Error F26
Problem: Memory corruption in control board

How to Fix Washer Error
1. Disconnect power at circuit breaker.
2. Remove control panel access cover.
3. Inspect main control board for physical damage.
4. Check all wire connections for proper seating and corrosion.
5. Test voltage supply to control board.
6. Attempt to reset by disconnecting power for 15 minutes.
7. If error persists, document all wire connections before removal.
8. Remove mounting screws and disconnect all connectors.
9. Install new main control board assembly.
10. Reconnect all harnesses and run diagnostic cycle to verify operation.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 2, 2026
How to Fix Kenmore Dryer Error LE
Problem: Motor failure – locked rotor or open winding

How to Fix Dryer Error
1. Turn off power at circuit breaker.
2. Remove front and rear access panels.
3. Inspect drive motor for overheating or unusual smells.
4. Test motor windings with multimeter for proper resistance readings.
5. Check motor start capacitor for bulging or leakage (if equipped).
6. Inspect drum belt for wear, tension, or damage.
7. Check drum rollers and bearings for smooth rotation.
8. If motor is faulty, disconnect electrical connectors and remove mounting bolts.
9. Install new drive motor assembly with proper alignment.
10. Reconnect wiring and test drum rotation at various speeds.
Still Not Working?

If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
February 2, 2026