Author: ApplianceFixGuide Team

Problem: Memory corruption in control board

How to Fix Washer Error

1. Disconnect power at circuit breaker.
2. Remove control panel access cover.
3. Inspect main control board for physical damage.
4. Check all wire connections for proper seating and corrosion.
5. Test voltage supply to control board.
6. Attempt to reset by disconnecting power for 15 minutes.
7. If error persists, document all wire connections before removal.
8. Remove mounting screws and disconnect all connectors.
9. Install new main control board assembly.
10. Reconnect all harnesses and run diagnostic cycle to verify operation.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Motor failure – locked rotor or open winding

How to Fix Dryer Error

1. Turn off power at circuit breaker.
2. Remove front and rear access panels.
3. Inspect drive motor for overheating or unusual smells.
4. Test motor windings with multimeter for proper resistance readings.
5. Check motor start capacitor for bulging or leakage (if equipped).
6. Inspect drum belt for wear, tension, or damage.
7. Check drum rollers and bearings for smooth rotation.
8. If motor is faulty, disconnect electrical connectors and remove mounting bolts.
9. Install new drive motor assembly with proper alignment.
10. Reconnect wiring and test drum rotation at various speeds.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Motor drive system overload protection

How to Fix Washer Error

1. Turn off power supply.
2. Remove front access panel.
3. Inspect drive motor for overheating or unusual smells.
4. Check motor wiring harness for damage or loose connections.
5. Test motor windings for proper resistance readings.
6. Inspect drive belt for wear, tension, or damage (if applicable).
7. Check tub bearings for smooth rotation and play.
8. If motor is drawing excessive current, replace motor assembly.
9. Verify proper mechanical alignment of all drive components.
10. Test motor operation under load conditions to verify proper function.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Heater element failure – open circuit

How to Fix Dryer Error

1. Turn off power at circuit breaker.
2. Remove rear access panel.
3. Disconnect electrical connections to heater element.
4. Test heater element for continuity with multimeter (should read 10-30 ohms).
5. If element is open, remove mounting screws securing element to heater housing.
6. Carefully extract old heater element and clean mounting surface.
7. Install new heater element with proper alignment.
8. Torque mounting screws to manufacturer specifications.
9. Reconnect electrical wiring and restore power.
10. Test heating cycle operation and verify proper temperature rise.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Thermistor error – temperature sensor failure

How to Fix Dryer Error

1. Disconnect power at circuit breaker.
2. Remove rear access panel.
3. Locate thermistor sensor on blower housing or heater assembly.
4. Disconnect electrical connector from thermistor.
5. Test sensor resistance with multimeter at room temperature.
6. Compare readings to manufacturer specifications chart.
7. If sensor is out of range, remove mounting screws and replace sensor.
8. Check wiring harness for damage or corrosion.
9. Clean sensor mounting area and ensure proper sealing.
10. Reconnect electrical connector and test temperature readings during cycle.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Temperature sensor circuit failure during heating cycle

How to Fix Washer Error

1. Disconnect power at circuit breaker.
2. Remove lower front access panel.
3. Locate temperature sensor on heater assembly or tub.
4. Disconnect electrical connector from sensor.
5. Test sensor resistance at various temperatures with multimeter.
6. Compare readings to manufacturer specifications chart.
7. If sensor is faulty, remove mounting screw and replace sensor.
8. Check wiring harness for damage or corrosion.
9. Inspect heater element connections for proper contact.
10. Restore power and test heating cycle with temperature verification.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Airflow restriction – lint filter or vent blockage

How to Fix Dryer Error

1. Turn off power supply and allow dryer to cool.
2. Remove and clean lint filter thoroughly with warm water and soap.
3. Inspect lint filter housing for debris buildup.
4. Check dryer vent hose for kinks, blockages, or excessive length.
5. Disconnect vent hose from dryer and clean interior duct.
6. Inspect external vent hood for obstructions (bird nests, debris).
7. Clean moisture sensor bars inside drum with rubbing alcohol.
8. Check blower wheel for debris or damage.
9. Verify proper airflow by feeling exhaust during operation.
10. Test drying cycle performance after cleaning all components.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Control board overheating protection activated

How to Fix Washer Error

1. Turn off pwer and allow washer to cool for 30 minutes.
2. Remove control panel and main access covers.
3. Inspect control boards for signs of overheating or burnt components.
4. Check cooling vents and fans for blockages or dust buildup.
5. Clean all cooling vents and fan blades with compressed air.
6. Verify proper airflow around control boards.
7. Test temperature sensors on control boards.
8. If board shows heat damage, replace affected control board.
9. Check for overloaded circuits or voltage fluctuations.
10. Test operation under normal load conditions to verify cooling.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Power failure during cycle operation

How to Fix Dryer Error

1. Check household circuit breaker for tripped condition.
2. Verify power outlet is functioning with another appliance.
3. Inspect power cord for damage or loose connections.
4. Check dryer power cord connection at terminal block inside machine.
5. Test voltag at terminal block with multimeter (should read 240V).
6. If power was restored, press START/PAUSE button to resume cycle.
7. If cycle won’t restart, disconnect power for 5 minutes to reset control boards.
8. Check for blown fuses on control boards if accessible.
9. Inspect main power supply wiring for damage or corrosion.
10. Test dryer operation after power restoration and reset procedures.

Browse all Kenmore error codes: Kenmore Error Codes

Problem: Door lock failure during high-speed spin

How to Fix Washer Error

1. Turn off power supply.
2. Open washer door fully.
3. Inspect door lock mechanism for wear or damage.
4. Test door lock solenoid with multimeter under load conditions.
5. Check door strike plate alignment and condition.
6. Inspect door gasket for proper sealing and alignment.
7. If lock assembly fails during high-speed tests, replace entire assembly.
8. Verify proper torque on mounting screws during installation.
9. Test door lock function at various spin speeds.
10. Ensure safety interlocks are functioning properly before final testing.

As an Amazon Associate, we earn from qualifying purchases through links on this page.

Browse all Kenmore error codes: Kenmore Error Codes