Amana Dishwasher error code
Amana Dishwasher Error F10
Heating element fault. There is an issue with the heating element.
Heating element fault. There is an issue with the heating element.
Try these first
Start here before buying a part or taking the appliance apart.
- 1Check 1
Check Water Supply: Ensure the water supply valve is fully open and that there are no kinks in the water inlet hose.
- 2Check 2
Inspect Float Switch: The float switch is a small plastic dome in the bottom of the tub that rises with the water level. Make sure it moves freely and is not stuck. Clean any debris from around the float.
- 3Check 3
Check Water Inlet Valve: Listen for a humming or buzzing sound from the water inlet valve when the dishwasher should be filling. If there's no sound, the valve may be faulty.
A quick explanation
What does F10 mean?
Heating element fault. There is an issue with the heating element.
The answer you came for
How to fix Amana dishwasher error F10
Start with the safest checks and work from simple to technical.
- 1
Step 1
1. Ensure the dishwasher is completely disconnected from power by switching off the circuit breaker.
- 2
Step 2
2. Pull the lower dish rack out and set it aside. This will give you a clear view of the heating element at the bottom of the tub.
- 3
Step 3
3. The heating element is held in place by two nuts. You will need to access the underside of the dishwasher to remove them.
- 4
Step 4
4. Carefully lay the dishwasher on its back on a soft surface to access the bottom.
- 5
Step 5
5. Disconnect the wires from the heating element terminals and then unscrew the retaining nuts.
- 6
Step 6
6. From inside the tub, lift out the old heating element. Install the new one (WPW10705575, W11084121) and secure it with the nuts from the bottom.
- 7
Step 7
7. Reconnect the wires, set the dishwasher upright, and restore power to test the heating function.
Read the additional checks from the current guide
How to Fix F10 Error (Step-by-Step) Ensure the dishwasher is completely disconnected from power by switching off the circuit breaker.Pull the lower dish rack out and set it aside. This will give you a clear view of the heating element at the bottom of the tub.The heating element is held in place by two nuts. You will need to access the underside of the dishwasher to remove them.Carefully lay the dishwasher on its back on a soft surface to access the bottom.Disconnect the wires from the heating element terminals and then unscrew the retaining nuts.From inside the tub, lift out the old heating element. Install the new one (WPW10705575, W11084121) and secure it with the nuts from the bottom.Reconnect the wires, set the dishwasher upright, and restore power to test the heating function.Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Amana Dishwasher Focused repair path: dishwasher fill, drain, wash motor, heating, leak, sensor, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check. Disconnect power before opening panels, then confirm the door latch, float, inlet valve, drain path, and harness connections are seated. Match the timing of the failure to the likely path: fill, wash circulation, drain, heat, leak detection, or control communication. Clear debris from filters, sump areas, spray arms, and the drain loop before treating the fault as a failed board. If a part is suspected, verify voltage or continuity where appropriate and match the complete Amana dishwasher model number before ordering. Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model. Verified Compatible Alternatives:WPW10705575
What may be causing it?
- Faulty water level sensor
- Stuck float switch
- Defective water inlet valve
- Kinked water inlet hose
These are possibilities to investigate, not proof that one part has failed.
Recommended part
Recommended part for this error code
Replacement part
OEM candidate: WPW10705575
Price noted in the current guide: $12-$54
Why this part is shown: It is associated with Amana Dishwasher error F10 in the current guide. The error code alone does not prove this part has failed.
Compatibility varies by model. Confirm that the Amazon listing includes your complete dishwasher model number before ordering.
You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.
Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.Replacement options
Ready to replace your dishwasher?
If repairing this dishwasher no longer feels worthwhile, compare three replacement paths below.
Why shop your replacement on Amazon?
-
Fast, free delivery
Prime members can get fast, free delivery on eligible items.
-
Convenient delivery options
Select large appliances may offer scheduled or Room of Choice delivery.
-
Haul-away options
Haul-away may be available for select appliances and delivery areas.
-
Installation help
Installation or assembly may be available on select items.
Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.
Value
$0-$499
Budget-friendly dishwashers in the $0-$499 range.
Shop Value Options on AmazonBest Overall
$500-$899
Balanced dishwashers in the $500-$899 range.
Shop Best Overall Options on AmazonPremium
$900-$2,000
Higher-end dishwashers in the $900-$2,000 range.
Shop Premium Options on AmazonMake the money decision
Repair or replace calculator
Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.
Safety first
Disconnect power before opening panels or touching internal parts.
When to stop
- Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
- Do not perform live-voltage testing unless you are trained and equipped for it.
- Use the exact model manual or service information before replacing electronic controls.
Free quick sheet
Get the Amana Dishwasher Error Code Quick Sheet
A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.
No spam. Unsubscribe anytime.