Error Code: IF01 Difficulty: Easy
Problem: The dishwasher has exceeded the permissible time for filling with water. The cycle may continue with a small amount of water until it is drained.
How to Fix IF01 Error (Step-by-Step)
- Turn off the dishwasher at the circuit breaker for 5 minutes to reset the electronics.
- Check that the water supply valve, usually located under your sink, is fully open.
- Gently pull the dishwasher out a few inches and inspect the water inlet hose for any kinks or twists that could be blocking water flow.
- Turn off the water supply valve and place a towel under the inlet hose connection at the dishwasher. Unscrew the hose and check the small filter screen inside for any debris or sediment. Clean it with a small brush if necessary.
- Reconnect the hose securely, ensuring it’s not cross-threaded. Turn the water supply back on and check for leaks.
- Ensure the dishwasher door is closing and latching properly, as the dishwasher will not fill if the door is not securely shut.
- Turn the circuit breaker back on and start a new cycle to see if the issue is resolved.
- Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher
Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
- Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset.
- Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
- Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
- Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
- Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Recommended Parts to Check
No exact official OEM part number is listed here because the correct Electrolux dishwasher part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
-
Electrolux dishwasher drain pumpCommon replacement category: Drain pumpFit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.Why this category can matter: standing-water, drain, and incomplete-cycle symptoms after filter and hose checks.
-
Electrolux dishwasher water inlet valveCommon replacement category: Water inlet valveFit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.Why this category can matter: fill or low-water symptoms after supply and float checks.
-
Electrolux dishwasher control boardCommon replacement category: Electronic control boardFit note: Exact OEM part number varies by complete Electrolux dishwasher model number. Confirm compatibility before buying.Why this category can matter: repeating control faults after latch, wiring, and power checks.
Before ordering: match the part to the complete Electrolux dishwasher model number on the appliance tag.
When It’s Better to Replace Than Repair
Dishwasher repairs can add up quickly when the pump, control, heater, or leak-related parts fail.
Confirm cabinet width, water line, drain routing, electrical connection, and panel style before ordering.
For repair parts, verify exact fit with the full dishwasher model number before buying; these links are general replacement-appliance shopping options.
- [OK]Drain pump or circulation pump failure
- [OK]Leaking tub, door, or float-switch issues
- [OK]Heater or control failures on an older unit
- [OK]Repeated poor washing or drying performance
Recommended Dishwasher Replacement Options
As an Amazon Associate, we earn from qualifying purchases.
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
More options (for a better recommendation)
⚡ Don’t Risk a DIY Fail!
Get the ‘Secret Service Mode’ Cheat Sheet for your Electrolux model. Includes an easy-to-read list of every error code and quick diagnostic tips.
✅ Join 15,000+ DIYers • Instant PDF Download
Browse More Codes
📖 View All Error Codes
Expert: Mike Sullivan
EPA Section 608 Certified Technician with 18+ years experience.
Read Editorial Standards →Browse all Electrolux error codes: Electrolux Error Codes
Leave a Reply