Electrolux Dishwasher error code
Electrolux Dishwasher Error I30-E30-3-FLASHES-3
Anti-flood system activated. A leak has been detected in the base of the dishwasher.
Anti-flood system activated. A leak has been detected in the base of the dishwasher.
Try these first
Start here before buying a part or taking the appliance apart.
- 1Turn the appliance off to the dishwasher immediately
Turn the appliance off to the dishwasher immediately at the circuit breaker to prevent electrical hazards.
- 2Pull the dishwasher out from under the counter
Pull the dishwasher out from under the counter to access the base pan.
- 3You will likely find water in the base
You will likely find water in the base pan. Use towels or a sponge to completely dry the area.
A quick explanation
What does I30-E30-3-FLASHES-3 mean?
Anti-flood system activated. A leak has been detected in the base of the dishwasher.
The answer you came for
How to fix Electrolux dishwasher error I30-E30-3-FLASHES-3
Start with the safest checks and work from simple to technical.
- 1
Turn the appliance off to the dishwasher immediately
Turn the appliance off to the dishwasher immediately at the circuit breaker to prevent electrical hazards.
- 2
Pull the dishwasher out from under the counter
Pull the dishwasher out from under the counter to access the base pan.
- 3
You will likely find water in the base
You will likely find water in the base pan. Use towels or a sponge to completely dry the area.
- 4
The anti-flood system is triggered by a float
The anti-flood system is triggered by a float switch (Part #154773201) that rises with the water level. Locate this switch in the base pan.
- 5
Once the pan is dry, the switch should
Once the pan is dry, the switch should reset. However, you must find the source of the leak (e.g., a loose hose, cracked pump, or bad seal).
- 6
After fixing the leak source, ensure the float
After fixing the leak source, ensure the float switch moves freely and is not stuck.
- 7
Reinstall the dishwasher, restore power, and run a
Reinstall the dishwasher, restore power, and run a cycle while monitoring for any new leaks.
- 8
Turn the appliance off, wait about 2 minutes,
Turn the appliance off, wait about 2 minutes, then turn it back on.
Read the additional checks from the current guide
How to Fix I30, E30, 3 FLASHES Error (Step-by-Step) Turn the appliance off to the dishwasher immediately at the circuit breaker to prevent electrical hazards.Pull the dishwasher out from under the counter to access the base pan.You will likely find water in the base pan. Use towels or a sponge to completely dry the area.The anti-flood system is triggered by a float switch (Part #154773201) that rises with the water level. Locate this switch in the base pan.Once the pan is dry, the switch should reset. However, you must find the source of the leak (e.g., a loose hose, cracked pump, or bad seal).After fixing the leak source, ensure the float switch moves freely and is not stuck.Reinstall the dishwasher, restore power, and run a cycle while monitoring for any new leaks.Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Dishwasher Focused repair path: dishwasher fill, drain, wash, heat, latch, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test. Disconnect power before opening panels, then confirm whether the Electrolux dishwasher repeats the same code after a clean reset. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure. Use the complete Electrolux dishwasher model number from the appliance tag before ordering any model-specific part. Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
Recommended part
Recommended part for this error code
Part listed in the current guide
OEM candidate: 154773201
Price noted in the current guide: $15-$35
Why this part is shown: It is associated with Electrolux Dishwasher error I30-E30-3-FLASHES-3 in the current guide. The error code alone does not prove this part has failed.
Compatibility varies by model. Confirm that the Amazon listing includes your complete dishwasher model number before ordering.
You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.
Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.Replacement options
Ready to replace your dishwasher?
If repairing this dishwasher no longer feels worthwhile, compare three replacement paths below.
Why shop your replacement on Amazon?
-
Fast, free delivery
Prime members can get fast, free delivery on eligible items.
-
Convenient delivery options
Select large appliances may offer scheduled or Room of Choice delivery.
-
Haul-away options
Haul-away may be available for select appliances and delivery areas.
-
Installation help
Installation or assembly may be available on select items.
Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.
Value
$0-$499
Budget-friendly dishwashers in the $0-$499 range.
Shop Value Options on AmazonBest Overall
$500-$899
Balanced dishwashers in the $500-$899 range.
Shop Best Overall Options on AmazonPremium
$900-$2,000
Higher-end dishwashers in the $900-$2,000 range.
Shop Premium Options on AmazonMake the money decision
Repair or replace calculator
Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.
Safety first
Disconnect power before opening panels or touching internal parts.
When to stop
- Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
- Do not perform live-voltage testing unless you are trained and equipped for it.
- Use the exact model manual or service information before replacing electronic controls.
Free quick sheet
Get the Electrolux Dishwasher Error Code Quick Sheet
A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.
No spam. Unsubscribe anytime.