Error Code: E60 Difficulty: Hard
Problem: Heating Error – Washer not heating water or taking too long to heat.
How to Fix E60 Error (Step-by-Step)
- Unplug the washer and turn off the water supply and confirm the error stays cleared during a full test cycle.
- Drain any water from the tub. You may need to use the drain pump filter or a siphon.
- Locate the heating element at the bottom of the outer tub. It is often accessible from the front or back of the machine by removing a lower panel.
- Disconnect the wires from the heating element. Use a multimeter set to continuity or resistance (ohms) to test the element. A reading of infinity indicates the element is broken and needs replacement.
- Locate the water temperature sensor, known as a thermistor, which is usually mounted near the heating element. Test its resistance with a multimeter; if it shows an open or shorted circuit, it must be replaced.
- If both the element and thermistor test correctly, inspect the wiring between these components and the main control board for any breaks or damage.
- If all other components are functional, the relay that controls the heating circuit on the main control board has failed, and the entire board will need to be replaced.
- Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Washer
Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
- Disconnect power before opening panels, then confirm whether the Electrolux washer repeats the same code after a clean reset.
- Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
- Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
- Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
- Use the complete Electrolux washer model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
- 137488301
- 137488302
- 1242941118
Recommended Parts to Check
No exact official OEM part number is listed here because the correct Electrolux washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
-
Electrolux washer drain pumpCommon replacement category: Drain pumpFit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying.Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks.
-
Electrolux washer water inlet valveCommon replacement category: Water inlet valveFit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying.Why this category can matter: fill and slow-fill symptoms after supply checks.
-
Electrolux washer door lockCommon replacement category: Door lock / latchFit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying.Why this category can matter: start, lock, or spin symptoms tied to door-lock feedback.
Before ordering: match the part to the complete Electrolux washer model number on the appliance tag.
⚡ Don’t Risk a DIY Fail!
Get the ‘Secret Service Mode’ Cheat Sheet for your Electrolux model. Includes an easy-to-read list of every error code and quick diagnostic tips.
✅ Join 15,000+ DIYers • Instant PDF Download
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Electrolux error codes: Electrolux Error Codes
When It’s Better to Replace Than Repair
Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
Here are a few signs it may be time to shop for a new one:
For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.
- ✓Appliance over 8-10 years old
- ✓Repair cost over 50% of replacement
- ✓Multiple recent breakdowns
- ✓Major component failure
Recommended Replacement Options
Why Upgrade via Amazon?
- Fast, Scheduled Delivery – You pick the date and time
- Expert Installation – Professional setup available for most models
- Old Appliance Haul-away – They’ll take your broken unit when they leave
- Easy Returns – Buy with confidence from a leader in customer service
As an Amazon Associate, we earn from qualifying purchases.
Leave a Reply