Error Code: E08 Difficulty: Hard
Problem: Heating error or defective heater.
How to Fix E08 Error (Step-by-Step)
- Completely disconnect the washer from the wall outlet and confirm the error stays cleared during a full test cycle.
- You will need to access the heating element, which is located at the bottom of the outer tub. This typically requires removing the front or rear service panel of the washer.
- Once you have access, carefully disconnect the two wires attached to the heating element terminals.
- Use a multimeter to test the element for continuity. Set the multimeter to the Ohms setting; a reading between 10-30 Ohms is normal. An infinite reading indicates the element is broken and needs replacement.
- To replace the element, loosen the nut in the center of its base and pull the old element out. This may require some force as it is sealed with a rubber gasket.
- Insert the new heating element, making sure the gasket is seated properly to prevent leaks. Tighten the nut to secure it.
- Reconnect the wires, reattach the service panel, and run a wash cycle with a hot water setting to confirm the repair.
- Turn the appliance off, wait about 2 minutes, then turn it back on.
What to Check Next on This Electrolux Washer
Focused repair path: washer fill, drain, spin, lock, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test.
- Disconnect power before opening panels, then confirm whether the Electrolux washer repeats the same code after a clean reset.
- Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response.
- Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage.
- Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure.
- Use the complete Electrolux washer model number from the appliance tag before ordering any model-specific part.
Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering.
- 137488302
Recommended Parts to Check
No exact official OEM part number is listed here because the correct Electrolux washer part can vary by complete model number. These are targeted part-category searches, not universal fit claims.
-
Electrolux washer drain pumpCommon replacement category: Drain pumpFit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying.Why this category can matter: drain, no-spin, or water-removal symptoms after hose and filter checks.
-
Electrolux washer water inlet valveCommon replacement category: Water inlet valveFit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying.Why this category can matter: fill and slow-fill symptoms after supply checks.
-
Electrolux washer door lockCommon replacement category: Door lock / latchFit note: Exact OEM part number varies by complete Electrolux washer model number. Confirm compatibility before buying.Why this category can matter: start, lock, or spin symptoms tied to door-lock feedback.
Before ordering: match the part to the complete Electrolux washer model number on the appliance tag.
⚡ Don’t Risk a DIY Fail!
Get the ‘Secret Service Mode’ Cheat Sheet for your Electrolux model. Includes an easy-to-read list of every error code and quick diagnostic tips.
✅ Join 15,000+ DIYers • Instant PDF Download
Still Not Working?
If the replacement part didn’t fix the issue, you may have a wiring problem or main board failure.
Browse all Electrolux error codes: Electrolux Error Codes
When It’s Better to Replace Than Repair
Sometimes replacing an appliance makes more financial sense than putting more money into repairs.
Here are a few signs it may be time to shop for a new one:
For repair parts, verify exact fit with the full washer model number before buying; these links are general replacement-appliance shopping options.
- ✓Appliance over 8-10 years old
- ✓Repair cost over 50% of replacement
- ✓Multiple recent breakdowns
- ✓Major component failure
Recommended Replacement Options
Why Upgrade via Amazon?
- Fast, Scheduled Delivery – You pick the date and time
- Expert Installation – Professional setup available for most models
- Old Appliance Haul-away – They’ll take your broken unit when they leave
- Easy Returns – Buy with confidence from a leader in customer service
As an Amazon Associate, we earn from qualifying purchases.
Leave a Reply