Skip to main content
Appliance Fix Guide

Electrolux Dryer error code

Electrolux Dryer Error E16

Vacuum switch - The vacuum switch was already closed when an attempt to start the dryer was made.

Vacuum switch - The vacuum switch was already closed when an attempt to start the dryer was made.

Updated Aug 18, 2026
✅ WORTH FIXINGParts under $100
Electrolux dryer repair guide for error E16
Error codeE16Dryer

Try these first

Start here before buying a part or taking the appliance apart.

  1. 1
    Check 1

    Unplug the dryer for a few minutes to reset the control board, then plug it back in.

  2. 2
    Check 2

    Ensure nothing is physically blocking the vacuum switch mechanism.

  3. 3
    Check 3

    Check the wiring connections to the vacuum switch for any loose or damaged wires.

A quick explanation

What does E16 mean?

Vacuum switch - The vacuum switch was already closed when an attempt to start the dryer was made.

The answer you came for

How to fix Electrolux dryer error E16

Start with the safest checks and work from simple to technical.

  1. 1

    Step 1

    1. Disconnect the dryer from the power source by unplugging it.

  2. 2

    Step 2

    2. Locate the vacuum or pressure switch (part 134057700). It is typically found near the blower housing and has a small rubber or plastic hose attached.

  3. 3

    Step 3

    3. Carefully remove the hose from the switch and inspect both the hose and the port on the switch for any lint or debris blockages.

  4. 4

    Step 4

    4. Blow gently through the hose to ensure it is completely clear.

  5. 5

    Step 5

    5. If the hose is clear, the switch itself may be faulty. Disconnect the wires from the switch.

  6. 6

    Step 6

    6. Use a multimeter to test for continuity across the switch terminals. A closed switch will show continuity when it should be open.

  7. 7

    Step 7

    7. If the switch is determined to be faulty, replace it with a new one and securely reattach the hose and wires.

Read the additional checks from the current guide

How to Fix E16 Error (Step-by-Step) Disconnect the dryer from the power source by unplugging it.Locate the vacuum or pressure switch (part 134057700). It is typically found near the blower housing and has a small rubber or plastic hose attached.Carefully remove the hose from the switch and inspect both the hose and the port on the switch for any lint or debris blockages.Blow gently through the hose to ensure it is completely clear.If the hose is clear, the switch itself may be faulty. Disconnect the wires from the switch.Use a multimeter to test for continuity across the switch terminals. A closed switch will show continuity when it should be open.If the switch is determined to be faulty, replace it with a new one and securely reattach the hose and wires.Turn the appliance off, wait about 2 minutes, then turn it back on.

What to Check Next on This Electrolux Dryer Focused repair path: dryer airflow, heating, motor, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test. Disconnect power before opening panels, then confirm whether the Electrolux dryer repeats the same code after a clean reset. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure. Use the complete Electrolux dryer model number from the appliance tag before ordering any model-specific part. Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering. &tag=appliancefixg-20Verified Compatible Alternatives:471886501

If the code comes back

Do not keep replacing parts based only on the code. Repeat the safe checks above. If the fault remains, stop and arrange qualified service rather than ordering from the code alone.

What may be causing it?

  • Faulty vacuum switch
  • Obstruction blocking the switch mechanism
  • Loose or damaged wiring to the vacuum switch

These are possibilities to investigate, not proof that one part has failed.

Recommended part

Recommended part for this error code

Replacement part

OEM candidate: 487197643

Price noted in the current guide: $20-$75

Why this part is shown: It is associated with Electrolux Dryer error E16 in the current guide. The error code alone does not prove this part has failed.

Compatibility varies by model. Confirm that the Amazon listing includes your complete dryer model number before ordering.

Amazon part link View recommended part on Amazon

You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Replacement options

Ready to replace your dryer?

If repairing this dryer no longer feels worthwhile, compare three replacement paths below.

Why shop your replacement on Amazon?

  • Fast, free delivery

    Prime members can get fast, free delivery on eligible items.

  • Convenient delivery options

    Select large appliances may offer scheduled or Room of Choice delivery.

  • Haul-away options

    Haul-away may be available for select appliances and delivery areas.

  • Installation help

    Installation or assembly may be available on select items.

Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Make the money decision

Repair or replace calculator

Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.

Safety first

Disconnect power before opening panels or touching internal parts.

When to stop
  • Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
  • Do not perform live-voltage testing unless you are trained and equipped for it.
  • Use the exact model manual or service information before replacing electronic controls.

Free quick sheet

Get the Electrolux Dryer Error Code Quick Sheet

A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.

No spam. Unsubscribe anytime.