Skip to main content
Appliance Fix Guide

Electrolux Dryer error code

Electrolux Dryer Error 9C

Software/config errors.

Software/config errors.

Updated Aug 18, 2026
⚠️ CHECK WARRANTY / AGE$100 - $250 Range
Electrolux dryer repair guide for error 9C
Error code9CDryer

Try these first

Start here before buying a part or taking the appliance apart.

  1. 1
    Check 1

    Disconnect the dryer from power for several minutes to reset the electronics.

  2. 2
    Check 2

    Inspect the wire connections between the main control board and the user interface board to ensure they are secure.

  3. 3
    Check 3

    Ensure no buttons on the control panel are stuck or contaminated.

A quick explanation

What does 9C mean?

Software/config errors.

The answer you came for

How to fix Electrolux dryer error 9C

Start with the safest checks and work from simple to technical.

  1. 1

    Step 1

    1. Unplug the dryer from the electrical outlet to ensure your safety.

  2. 2

    Step 2

    2. Access the main control board, which is typically located behind the top or rear panel. You will need a screwdriver to remove the panel screws.

  3. 3

    Step 3

    3. Before disconnecting anything, take a clear photo of the wire connections to the control board to use as a reference.

  4. 4

    Step 4

    4. Carefully disconnect all wire harnesses from the old control board. Most connectors have a small tab that needs to be pressed to release.

  5. 5

    Step 5

    5. Remove the screws or clips holding the old control board in place and gently lift it out.

  6. 6

    Step 6

    6. Install the new control board, securing it with the original screws or clips.

  7. 7

    Step 7

    7. Reconnect all wire harnesses to the new board, referring to the photo you took earlier to ensure they are in the correct positions. Reassemble the dryer and test its operation.

Read the additional checks from the current guide

How to Fix 9C Error (Step-by-Step) Unplug the dryer from the electrical outlet to ensure your safety.Access the main control board, which is typically located behind the top or rear panel. You will need a screwdriver to remove the panel screws.Before disconnecting anything, take a clear photo of the wire connections to the control board to use as a reference.Carefully disconnect all wire harnesses from the old control board. Most connectors have a small tab that needs to be pressed to release.Remove the screws or clips holding the old control board in place and gently lift it out.Install the new control board, securing it with the original screws or clips.Reconnect all wire harnesses to the new board, referring to the photo you took earlier to ensure they are in the correct positions. Reassemble the dryer and test its operation.Turn the appliance off, wait about 2 minutes, then turn it back on.

What to Check Next on This Electrolux Dryer Focused repair path: dryer airflow, heating, motor, sensor, and control checks. Do not treat the fault as reset-only if it keeps returning; use the failed function to choose the next test. Disconnect power before opening panels, then confirm whether the Electrolux dryer repeats the same code after a clean reset. Match the symptom to the part of the cycle or function that fails: fill, drain, heat, cool, spin, latch, ignite, fan, sensor, or control response. Inspect simple causes first: airflow, water supply, drain path, door closure, filter, venting, wiring connectors, and visible damage. Use meter testing or service diagnostics before replacing electronic controls, because wiring, switches, sensors, and loads can mimic board failure. Use the complete Electrolux dryer model number from the appliance tag before ordering any model-specific part. Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Electrolux model number from the appliance tag before ordering. &tag=appliancefixg-20Verified Compatible Alternatives:5304505611

If the code comes back

Do not keep replacing parts based only on the code. Repeat the safe checks above. If the fault remains, stop and arrange qualified service rather than ordering from the code alone.

What may be causing it?

  • Faulty user interface board
  • Failed main control board
  • Loose connection between the main control board and the user interface board

These are possibilities to investigate, not proof that one part has failed.

Recommended part

Recommended part for this error code

Replacement part

OEM candidate: 134994600

Price noted in the current guide: $160-$210

Why this part is shown: It is associated with Electrolux Dryer error 9C in the current guide. The error code alone does not prove this part has failed.

Compatibility varies by model. Confirm that the Amazon listing includes your complete dryer model number before ordering.

Amazon part link View recommended part on Amazon

You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Replacement options

Ready to replace your dryer?

If repairing this dryer no longer feels worthwhile, compare three replacement paths below.

Why shop your replacement on Amazon?

  • Fast, free delivery

    Prime members can get fast, free delivery on eligible items.

  • Convenient delivery options

    Select large appliances may offer scheduled or Room of Choice delivery.

  • Haul-away options

    Haul-away may be available for select appliances and delivery areas.

  • Installation help

    Installation or assembly may be available on select items.

Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Make the money decision

Repair or replace calculator

Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.

Safety first

Disconnect power before opening panels or touching internal parts.

When to stop
  • Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
  • Do not perform live-voltage testing unless you are trained and equipped for it.
  • Use the exact model manual or service information before replacing electronic controls.

Free quick sheet

Get the Electrolux Dryer Error Code Quick Sheet

A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.

No spam. Unsubscribe anytime.