Skip to main content
Appliance Fix Guide

Frigidaire Refrigerator error code

Frigidaire Refrigerator Error E1

Refrigerator thermistor (temperature sensor) is open.

Refrigerator thermistor (temperature sensor) is open.

Updated Aug 18, 2026
✅ WORTH FIXINGParts under $100
Frigidaire refrigerator repair guide for error E1
Error codeE1Refrigerator

Try these first

Start here before buying a part or taking the appliance apart.

  1. 1
    Check 1

    Unplug the refrigerator.

  2. 2
    Check 2

    Locate the sensor in the fresh food section, typically behind a small plastic cover.

  3. 3
    Check 3

    Ensure the sensor's wire connector is firmly plugged in.

A quick explanation

What does E1 mean?

Refrigerator thermistor (temperature sensor) is open.

The answer you came for

How to fix Frigidaire refrigerator error E1

Start with the safest checks and work from simple to technical.

  1. 1

    Step 1

    1. Unplug the refrigerator from the power outlet for safety.

  2. 2

    Step 2

    2. Empty the fresh food section to get clear access to the interior walls and ceiling.

  3. 3

    Step 3

    3. Locate the thermistor cover. It's a small, vented plastic housing, usually on the upper right side wall or near the control housing at the top.

  4. 4

    Step 4

    4. Use a small flathead screwdriver to gently pry the cover off, exposing the sensor probe.

  5. 5

    Step 5

    5. Disconnect the wire harness attached to the old thermistor. It will have a small clip you need to press.

  6. 6

    Step 6

    6. Connect the new thermistor to the wire harness until it clicks into place.

  7. 7

    Step 7

    7. Snap the plastic cover back on, return food to the refrigerator, and plug the unit back in.

Read the additional checks from the current guide

How to Fix E1 Error (Step-by-Step) Unplug the refrigerator from the power outlet for safety and confirm the error stays cleared during a full test cycle.Empty the fresh food section to get clear access to the interior walls and ceiling.Locate the thermistor cover. It's a small, vented plastic housing, usually on the upper right side wall or near the control housing at the top.Use a small flathead screwdriver to gently pry the cover off, exposing the sensor probe.Disconnect the wire harness attached to the old thermistor. It will have a small clip you need to press.Connect the new thermistor to the wire harness until it clicks into place.Snap the plastic cover back on, return food to the refrigerator, and plug the unit back in.Turn the appliance off, wait about 2 minutes, then turn it back on.

What to Check Next on This Frigidaire Refrigerator Focused repair path: refrigerator door, airflow, sensor, defrost, dispenser, and control checks. Do not treat this as a reset-only problem if the code keeps returning; use what the appliance does during the failed part of the cycle to choose the next check. Confirm the doors close fully, the gaskets seal, and the display is not reacting to a door left open or a blocked switch. Check for blocked vents, heavy frost, stalled fans, warm compartments, or recent power interruptions before replacing electronic parts. If the code involves temperature or airflow, inspect the evaporator fan, thermistor, defrost path, wiring, and control connections. If the symptom follows a door or dispenser event, check the switch, harness, hinge wiring, and connector seating first. Use the full Frigidaire refrigerator model number before buying parts because sensors, boards, fans, and switches are model-specific. Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Frigidaire model number from the appliance tag before ordering. The same error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, or control boards depending on the exact model. &tag=appliancefixg-20Verified Compatible Alternatives:Refrigerator Temperature Sensor

If the code comes back

Do not keep replacing parts based only on the code. Repeat the safe checks above. If the fault remains, stop and arrange qualified service rather than ordering from the code alone.

What may be causing it?

  • Failure of the thermistor (sensor) in the fresh food compartment.
  • Loose or damaged sensor wiring.

These are possibilities to investigate, not proof that one part has failed.

Recommended part

Recommended part for this error code

Refrigerator Temperature Sensor

Price noted in the current guide: $20-$50

Why this part is shown: It is associated with Frigidaire Refrigerator error E1 in the current guide. The error code alone does not prove this part has failed.

Compatibility varies by model. Confirm that the Amazon listing includes your complete refrigerator model number before ordering.

Amazon part link View recommended part on Amazon

You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Replacement options

Ready to replace your refrigerator?

If repairing this refrigerator no longer feels worthwhile, compare three replacement paths below.

Why shop your replacement on Amazon?

  • Fast, free delivery

    Prime members can get fast, free delivery on eligible items.

  • Convenient delivery options

    Select large appliances may offer scheduled or Room of Choice delivery.

  • Haul-away options

    Haul-away may be available for select appliances and delivery areas.

  • Installation help

    Installation or assembly may be available on select items.

Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Make the money decision

Repair or replace calculator

Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.

Safety first

Disconnect power before opening panels or touching internal parts.

When to stop
  • Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
  • Do not perform live-voltage testing unless you are trained and equipped for it.
  • Use the exact model manual or service information before replacing electronic controls.

Free quick sheet

Get the Frigidaire Refrigerator Error Code Quick Sheet

A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.

No spam. Unsubscribe anytime.