Skip to main content
Appliance Fix Guide

Amana Dryer error code

Amana Dryer Error E1

Indicates an issue with the thermistor, specifically an open circuit. This can be caused

Indicates an issue with the thermistor, specifically an open circuit. This can be caused by a faulty thermistor or a wiring problem.

ModerateStart with 5-15 minutes of safe checks
✅ WORTH FIXINGParts under $100
Amana dryer repair guide for error E1
Error codeE1Dryer

Try these first

Start here before buying a part or taking the appliance apart.

  1. 1
    Disconnect the dryer from its power source by

    Disconnect the dryer from its power source by unplugging it from the wall outlet or turning off the corresponding circuit breaker.

  2. 2
    Move the dryer away from the wall to

    Move the dryer away from the wall to access the rear panel. Remove the screws holding the panel in place and set it aside.

  3. 3
    Locate the thermistor

    Locate the thermistor. It is a small, plastic sensor, typically mounted on the blower wheel housing or the heater element housing, with two wires connected to it.

A quick explanation

What does E1 mean?

Indicates an issue with the thermistor, specifically an open circuit. This can be caused by a faulty thermistor or a wiring problem.

The answer you came for

How to fix Amana dryer error E1

Start with the safest checks and work from simple to technical.

  1. 1

    Disconnect the dryer from its power source by

    Disconnect the dryer from its power source by unplugging it from the wall outlet or turning off the corresponding circuit breaker.

  2. 2

    Move the dryer away from the wall to

    Move the dryer away from the wall to access the rear panel. Remove the screws holding the panel in place and set it aside.

  3. 3

    Locate the thermistor

    Locate the thermistor. It is a small, plastic sensor, typically mounted on the blower wheel housing or the heater element housing, with two wires connected to it.

  4. 4

    Carefully disconnect the wire harness from the old

    Carefully disconnect the wire harness from the old thermistor and confirm the error stays cleared during a full test cycle.

  5. 5

    Remove the single screw that fastens the thermistor

    Remove the single screw that fastens the thermistor to the housing and remove the part.

  6. 6

    Install the new thermistor by securing it with

    Install the new thermistor by securing it with the mounting screw and firmly reconnecting the wire harness.

  7. 7

    Turn the appliance off, wait about 2 minutes,

    Turn the appliance off, wait about 2 minutes, then turn it back on.

Read the additional checks from the current guide

How to Fix E1 Error (Step-by-Step) Disconnect the dryer from its power source by unplugging it from the wall outlet or turning off the corresponding circuit breaker.Move the dryer away from the wall to access the rear panel. Remove the screws holding the panel in place and set it aside.Locate the thermistor. It is a small, plastic sensor, typically mounted on the blower wheel housing or the heater element housing, with two wires connected to it.Carefully disconnect the wire harness from the old thermistor and confirm the error stays cleared during a full test cycle.Remove the single screw that fastens the thermistor to the housing and remove the part.Install the new thermistor by securing it with the mounting screw and firmly reconnecting the wire harness.Turn the appliance off, wait about 2 minutes, then turn it back on.

What to Check Next on This Amana Dryer Focused repair path: dryer airflow, heating, sensor, motor, door switch, belt, and control checks. Do not treat a returning fault as a reset-only problem; use the point in the cycle where the fault appears to choose the next check. Disconnect power before inspection, then clear the lint screen, blower area, vent run, and exterior hood before replacing heat parts. Confirm whether the dryer starts, tumbles, heats, and advances through the cycle; the missing function narrows the repair path. For heat faults, inspect airflow first, then the thermal fuse, thermistor, element or gas ignition path, wiring, and control output. For start or tumble faults, check the door switch, belt switch, motor circuit, harness, and control connections before ordering parts. Check, inspect, clean, test, measure, remove, reconnect, clear, and replace parts only when the symptom supports that path. If these checks point toward a part, verify the complete Amana model number from the appliance tag before ordering. Similar error wording can use different valves, sensors, pumps, motors, heaters, locks, switches, fans, or control boards depending on the exact model. Next Steps and Parts &tag=appliancefixg-20Verified Compatible Alternatives:WP35001191

If the code comes back

Do not keep replacing parts based only on the code. Repeat the safe checks above. If the fault remains, stop and arrange qualified service rather than ordering from the code alone.

Recommended part

Recommended part for this error code

Part listed in the current guide

OEM candidate: WP8577274

Price noted in the current guide: $15-$71

Why this part is shown: It is associated with Amana Dryer error E1 in the current guide. The error code alone does not prove this part has failed.

Compatibility varies by model. Confirm that the Amazon listing includes your complete dryer model number before ordering.

Amazon part link View recommended part on Amazon

You can open the recommendation now. Check model compatibility on the Amazon page before purchasing.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Replacement options

Ready to replace your dryer?

If repairing this dryer no longer feels worthwhile, compare three replacement paths below.

Why shop your replacement on Amazon?

  • Fast, free delivery

    Prime members can get fast, free delivery on eligible items.

  • Convenient delivery options

    Select large appliances may offer scheduled or Room of Choice delivery.

  • Haul-away options

    Haul-away may be available for select appliances and delivery areas.

  • Installation help

    Installation or assembly may be available on select items.

Delivery and service options, fees, and availability vary by item, seller, and delivery ZIP code. Confirm available services at Amazon checkout.

Affiliate disclosure: qualifying purchases may earn this site a commission at no additional cost to you.

Make the money decision

Repair or replace calculator

Use the age and total repair estimate to get a simple comparison. This is guidance, not a guarantee.

Safety first

Disconnect power before opening panels or touching internal parts.

When to stop
  • Stop if you see burned wiring, melted connectors, water near electrical parts, or a gas smell.
  • Do not perform live-voltage testing unless you are trained and equipped for it.
  • Use the exact model manual or service information before replacing electronic controls.

Free quick sheet

Get the Amana Dryer Error Code Quick Sheet

A concise reference with code meanings, severity, first checks, and when it is time to stop and call for service.

No spam. Unsubscribe anytime.